How much tile adhesive to use for one square meter tile

As we all know, tile laying requires cement mortar in addition to adhesives. So how much adhesive is needed for a square meter tile?

How much tile adhesive to use for one square meter tile?

1 square meter tiles need to use about 3.5 pounds of adhesive, the thickness of about 3-5 cm, but the final dosage will be affected by the following four aspects, one is the size of the pasted tiles, the second is the construction technology of the workers, the third is the construction of the degree of wear and tear, and the fourth is the surface smoothness, which is different from any of them, the dosage of adhesive will be changed.

Based on similar questions, I'm going to give a unified answer here:
How much tile adhesive per square meter?
Also 3.5 lbs per square meter
How much tile glue per square meter?
Here glue and adhesive mean the same thing, glue is an everyday word, about this question, you can also use the answer in this article, the amount of use is equivalent to about 1.6kg per square meter
How much tile adhesive per square foot?
Here I want to convert, how many square feet per square foot, according to the conversion, each square foot about using 0.3 pounds of tile adhesive, that is, 0.136kg.
Also how many bags of tile adhesive per square meter?how much tile adhesive do i need per square meter?how much tile adhesive do i need per square foot?how many tile adhesive per square meter? and other questions are the same answer, many friends in the conversion details did not understand, here are unified explanation.The uniform answer is £3.50 per square meter, or 0.16kg per square meter.Of course, the answer here is an estimated figure, and you have to test it according to your own situation, for example, if the viscosity is low, you can increase the amount you use or change to a higher viscosity grade.

Tile tiling notes

1. Tile tiling order

In the home improvement, workers will generally lay tiles and then floor tiles, so that it is more convenient to tile paving. But before paving to clean up the wall of impurities, and to start from the corner or windows and doors, and then according to the requirements of the order from top to bottom, from left to right to paving.

2. Tile soak

Tile back has a lot of tiny holes, so before the wall to soak, soak time can not be less than 30 minutes, and wait until the tiles will not be bubbling before use, otherwise paving the tiles will be in the cement mortar is the moisture sucked away, resulting in tiles appearing hollow drums, falling off and other problems.

3. Tile positioning row tile

Before construction, to do a good job of placing lines and rows of tiles, so that the construction of tiles will be more neat. Note that in the emission of non-integrated tiles are best discharged in the corner, and a wall is best not to paste two rows of non-integrated tiles. In addition, the width of non-integrated tiles should be more than one-third of the whole tile, otherwise it will affect the beauty of the wall.

4. Tile gap width uniform

In construction, the horizontal and vertical seams should be flat, even width. If you meet the pipeline or switch, use the whole set of cut tiles, do not use non-tile patchwork, and not a one-time paving to the top, to avoid falling due to unstable paving injuries.

5. Tile paving

After paving and drying the tiles, to see if there are problems such as drums and colour differences, if the drums are more than 5% is considered unqualified, need to be re-paved.

So how to configure the best tile adhesive?

To 1 kg to proportion, the main cement, sand, hydroxypropyl methyl cellulose, dispersible latex powder, etc., different grades of tile adhesive formula is slightly different, according to the actual needs of the proportion, to achieve the best results.
Common tile adhesive formula ingredients
The formula of common tile adhesive usually includes the following ingredients:

√ cement: 330g
√ Sand: 690g (30-50 mesh)
√ Hydroxypropyl methyl cellulose: 4g
√ Redispersible latex powder: 10g
√ Calcium formate: 5g12
Composition of high adhesion tile adhesive formula
The formula for high tack adhesive tile adhesive then includes:
√ cement: 350g
√ Sand: 625g
√ hydroxypropyl methyl cellulose: 2.5g
√ Calcium formate: 3g
√ polyvinyl alcohol: 1.5g
√ Butyl Styrene Rubber Powder: 18g

Role of Hydroxypropyl Methyl Cellulose

Hydroxypropyl Methyl Cellulose in the formula it has high water retention, HPMC is a thickener in tile adhesive formula with good water retention. And the amount of hydroxypropyl methyl cellulose should be strictly controlled, otherwise it will cause the surface of the tile adhesive peeling, in general, cement-based tile adhesive formulations, HPMC additive amount of 1.5-2, the specific additive amount is also subject to the local climate, temperature, humidity and other influences.
The use of HPMC in tile adhesive formulations can shorten the construction time and make the construction faster and more efficient. It improves workability and reduces costs.

Basically this formula fully meets the normal needs, special attention is paid to the amount of hydroxypropyl methyl cellulose, dispersible latex powder, which is related to the tile adhesive can be the key to the success of the ratio, and reliable hydroxypropyl methyl cellulose manufacturer can provide you with high quality products, choose to use the excellent performance of the hpmc products on the construction of the The choice of hpmc products with excellent performance will play a good role in promoting the smooth progress of the construction project. With MIKEM's wide range of products, you can formulate the perfect tile adhesive. If you are interested in our products or would like to place an order, please contact us.